Owens Corning Wall Insulation Nationwide

Owens Corning Wall Insulation in Burbank: What to Know First

Wall insulation using Owens Corning products in Burbank typically costs $1,800 to $6,400 depending on wall type, access method, and square footage. Most jobs are completed in a single visit, often within one day. We’re an independent Owens Corning service provider, not a manufacturer-authorized shop, which means we recommend what actually works for your Burbank home rather than what a brand program tells us to sell.

Call (747) 837-5834

This page is for Burbank homeowners who either already have Owens Corning insulation in their walls and suspect it’s failing, or who are considering Owens Corning products for a wall insulation upgrade. If your rooms run hot in August, cold in January, or you hear your neighbor’s dog like it’s in your living room, call (747) 837-5834 and a live person answers. Always. No voicemail, no phone tree, no call-back tomorrow.

Key takeaways:

• We diagnose before we recommend. Burbank homes built before 1980 often have zero wall insulation, and homes built 1980-2010 frequently have fiberglass batts that were installed incorrectly.
• Owens Corning makes several lines we use and trust: EcoTouch, Thermafiber, and FOAMULAR are the ones that show up most in Burbank wall work.
• Drill-and-fill is the standard method for existing walls in Burbank. New construction or open-wall remodels take a different approach entirely.
• Every wall insulation job carries our 90-Day Done Right Promise. If it isn’t right, we make it right.

How Owens Corning Products Fail - and How We Fix Them

Owens Corning fiberglass is a solid product. Neil Ashford has pulled enough of it out of Burbank walls to know exactly where it goes wrong. Here’s what we see most often:

• EcoTouch batts compressed behind outlet boxes. This is the number one failure we find in Burbank homes from the 1990s and 2000s. Installers stuffed the batt behind an electrical box and crushed it to half its R-value. The fix: remove the compressed section, re-cut properly around the box, and seal the electrical penetration with foam before the batt goes back. Compression robs R-value, and no amount of wishful thinking gets it back.
• Settling in older loose-fill attic-to-wall transitions. In two-story Burbank homes, blown-in fiberglass from the attic can settle away from the top plate, opening a thermal channel at the floor line of the upper story. We top up the wall cavity from the attic side and air-seal the junction so the warm air stops escaping.
• Thermafiber mineral wool installed without an air barrier in stucco Burbank homes. Thermafiber resists moisture and fire beautifully, but in stucco exteriors with no house wrap, Burbank’s winter rains can drive moisture through hairline cracks into the insulation cavity. The fix is drainage and sealing, not just re-insulating. We address the envelope, not just the fill.
• FOAMULAR rigid board with taped seams that failed. On Burbank garage conversions and bonus-room additions, we see FOAMULAR XPS boards where the installer used cheap tape that peeled within two years. The air gap that forms is worse than having no board at all in some spots. We replace with proper manufacturer-compatible tape and furring that holds the board tight.
• Old R-11 walls in 1950s Burbank tract homes. These aren’t Owens Corning failures, they’re just under-insulated to begin with. Three inches of fiberglass squeezed into a 2×4 cavity is not doing anything. We cut access holes, dense-pack the cavity with blown-in fiberglass or injection foam, and patch to match the existing stucco or drywall texture.

Our Owens Corning Wall Insulation Process

Here’s exactly how a typical Owens Corning wall insulation job goes at a Burbank home, from the first call to the final walkthrough:

1. 1
   Live call and scheduling. You call (747) 837-5834. A real person answers, asks about your home’s age, comfort complaints, and wall type, and books a diagnostic visit. Most appointments happen within days, not weeks.
2. 2
   Wall inspection and diagnosis. A background-checked, uniformed technician arrives and checks the obvious first: existing insulation depth, air leaks, stud spacing, and any signs of moisture or pests. If you have a 1920s-1960s Burbank house with lathe and plaster, we plan for that. If it’s 1980s stucco, that changes the access method.
3. 3
   The recommendation, in plain English. We tell you what we found, what Owens Corning product fits the job, and what it costs. No three-bid games. The price we quote is the price on the invoice unless we find something structurally wrong behind the wall that nobody could have seen.
4. 4
   Drill, fill, and seal. For existing walls, we drill access holes from the exterior or interior (often 2-inch cores in the stucco or drywall), dense-pack the cavity, seal air leaks at outlets and top plates, and patch to match. For open-wall remodels, we install properly fitted batts or rigid board with the air barrier detailed correctly.
5. 5
   Test and verify. We check the fill density where possible, confirm air sealing at key junctions, and walk you through what we did. You’ll see the access points and know they were patched right.
6. 6
   Done Right Promise in writing. Every job gets our 90-Day Done Right Promise. If the insulation settles, the patches crack, or anything else didn’t hold up, we come back and make it right. No argument, no fine print.

What Owens Corning Wall Insulation Costs in Burbank

Burbank wall insulation pricing depends on three things: how many walls, what’s currently in them, and whether we access from outside or inside. Here are the ranges we quote most often:

• Drill-and-fill dense-pack for an existing 1,200 sq ft Burbank home: $3,200 to $5,800. This includes access, filling all exterior walls, patching, and air sealing around outlets and window frames.
• Single-room soundproofing between walls or floors: $900 to $2,200 per room. Thermafiber mineral wool is our usual recommendation here because it blocks sound transfer far better than standard fiberglass batts.
• New construction or open-wall batt installation: $1,800 to $3,400 for a typical Burbank single-story, labor and materials included. Owens Corning EcoTouch R-15 in 2×4 cavities, or R-21 in 2×6.
• Exterior rigid board (FOAMULAR) on a stucco retrofit or garage wall: $2,400 to $6,400 depending on square footage and whether old stucco has to come off first.

What moves the price: access difficulty (second story, tight lot lines, lath and plaster), whether we need to remove old insulation first, and the condition of your wall sheathing. Discounts that apply: $50 off any repair over $250, a permanent 5% senior and veteran discount, and if you want a full-home look before deciding, our $89 seasonal tune-up includes a visual inspection of your wall and attic insulation. Call (747) 837-5834 for an exact quote. Estimates are free, and the person who answers won’t pressure you into a sale.

Why Burbank Homeowners Call Warmline Insulation Co. for Owens Corning Work

We’ve been in business since 2011, and most of our Burbank wall insulation work comes from referrals. That’s not an accident. Here’s why:

First, we know Owens Corning products beyond the marketing sheet. Neil Ashford has spent nearly two decades pulling apart walls in Burbank, including more older Magnolia Park houses than he can count, and he taught his techs what he learned the hard way. We know when EcoTouch is the right call and when Thermafiber does the job better. We don’t upsell product lines. We match the material to the wall, the climate, and the budget.

Second, we’re full-spectrum. If your wall insulation problem is actually an attic air-sealing problem, or a crawl space issue feeding moisture into your stud bays, we see that in the same visit. We don’t hand you off to another contractor. One crew, one diagnosis, most jobs done in a single visit.

Third, our backup plan is real. If Owens Corning stock is backordered on the specific product your Burbank job needs, we carry and install Reflectix as a secondary option for radiant-barrier wall applications, plus Rockwool, CertainTeed, Icynene, Johns Manville, Knauf, and GreenFiber. You get the right material, not just the one easiest for us to source.

Neil says it best: “Good insulation shouldn’t be something you think about - that means it’s working.” What you do think about is the 90-Day Done Right Promise if anything doesn’t hold up. We answer the phone, we show up on time, and we fix it right. Licensed, insured, and proud to serve Burbank and the surrounding area.

FAQs